How Can Indian and International Manufacturers Obtain BIS Certification for Tungsten Filament Lamps?

Tungsten filament lamps, also called GLS or incandescent bulbs, are still made and sold in large numbers for homes, shops and decorative fittings. If you manufacture or import them for the Indian market, you need BIS certification for tungsten filament lamps before you can legally sell them. This guide explains what it involves and how both Indian and international manufacturers can get it.

What Is BIS Certification for Tungsten Filament Lamps?

The Bureau of Indian Standards (BIS) is India’s national standards body. Certain products must carry the ISI Mark, which shows that the product meets an Indian Standard. For tungsten filament lamps, the relevant standard is IS 418:2004, “Tungsten filament lamps for domestic and similar general lighting purposes.” It covers general service lamps up to 100 W.

Certification falls under Scheme-I of the BIS Conformity Assessment Regulations, 2018, issued under the BIS Act, 2016. Under this scheme BIS grants a licence to use the ISI Mark on products that pass testing and factory checks.

Why Is It Mandatory?

These lamps are covered by a government Quality Control Order, so selling, importing or storing them without the ISI Mark can lead to penalties, including seizure of goods and fines. Beyond the legal requirement, certification also:

  • Confirms safe insulation, correct marking and interchangeable caps and holders
  • Builds trust with distributors, retailers and consumers
  • Gives you access to the full Indian market, including government and institutional buyers
  • Reduces the risk of customs delays for imported goods

What Does IS 418:2004 Test?

The standard checks safety and performance. Typical areas include:

  • Marking and legibility of rated voltage and wattage
  • Cap and lamp dimensions, so the lamp fits standard holders
  • Insulation resistance and electric strength
  • Protection against live parts
  • Performance such as rated life and luminous output

The 2006 amendment points to IS 15518 (Part 1) for the safety requirements. Always check the latest amendments on the BIS portal before you start.

How Indian Manufacturers Can Get BIS Certification

Step 1: Understand the standard. Buy IS 418:2004 from BIS and compare it with your design, materials and production line.

Step 2: Set up a testing facility. BIS expects a basic in-house laboratory that can run routine tests on production samples.

Step 3: Apply online. Register on the BIS portal and submit the application for a Scheme-I licence along with the fee.

Step 4: Submit documents. You will usually need:

  • Business registration proof (GST, MSME or incorporation certificate)
  • Factory address and layout
  • List of machinery and testing equipment
  • Manufacturing process flow chart
  • Details of the authorised signatory
  • Declaration of conformity to IS 418

Step 5: Factory inspection and sampling. A BIS officer visits your plant, reviews your quality control system and draws samples.

Step 6: Independent testing. Samples are tested at a BIS-recognised laboratory. Failed parameters must be corrected and retested.

Step 7: Licence grant. After a successful inspection and test report, BIS grants the licence and you can print the ISI Mark on your lamps. Keep paying the annual marking fee and expect surveillance audits.

For a well-prepared Indian manufacturer, the process is often quoted at around 30 days. Actual time depends on documentation quality, lab availability and inspection scheduling.

How International Manufacturers Can Get BIS Certification

Overseas factories apply under the Foreign Manufacturers Certification Scheme (FMCS), which is also part of Scheme-I. The core steps are similar, with a few extra requirements:

  1. Appoint an Authorised Indian Representative (AIR). The AIR is an Indian resident or company that deals with BIS on your behalf. They must be appointed by a formal authorisation letter.
  2. Submit the application and fee. The application is filed through the BIS portal, usually with the AIR’s help.
  3. Provide documents. These include the manufacturer’s registration, factory details, process chart, equipment list, an agreement to the Scheme of Inspection and Testing (SIT) and the AIR authorisation.
  4. Get an inspection. BIS inspects the overseas factory, and the manufacturer bears the inspector’s travel and stay costs.
  5. Test samples. Samples are tested at a BIS-recognised lab, sometimes in India.
  6. Receive the licence and pay marking fees. Once granted, you can apply the ISI Mark and export to India.

Foreign applications generally take longer because of the overseas inspection and logistics. Many consultants quote roughly 120 to 180 days, but treat this as an estimate. Timelines vary with country, lab queues and how complete your file is.

Common Mistakes to Avoid

  • Submitting incomplete or inconsistent documents
  • Having no calibrated testing equipment at the factory
  • Using lamp markings that don’t match the standard
  • Ignoring the annual marking fee and surveillance audits
  • Appointing an AIR without checking their BIS experience

Tips for a Faster Approval

  • Run a pre-assessment test on your own lamps before applying
  • Keep calibration certificates and test records ready for the inspector
  • Train your quality staff on IS 418 requirements
  • Respond to BIS queries quickly
  • Check the BIS website for current fees, forms and rules, since procedures are updated from time to time

Read also How Can German Manufacturers Obtain BIS FMCS Certification in India?

Frequently Asked Questions (FAQs)

  1. Is BIS certification mandatory for tungsten filament lamps?
    Yes. Tungsten filament general service lamps up to 100 W fall under compulsory ISI certification against IS 418:2004.
  2. Which BIS scheme applies to these lamps?
    Scheme-I (the ISI Mark scheme). Indian manufacturers apply directly, and foreign manufacturers apply under FMCS.
  3. Can a foreign manufacturer apply without an Indian representative?
    No. An Authorised Indian Representative is required to coordinate with BIS.
  4. How long does certification take?
    Indian manufacturers are often quoted around 30 days, and foreign manufacturers several months. These are estimates, and your actual timeline depends on documents, testing and inspection.
  5. Is factory inspection required?
    Yes. BIS inspects the factory to verify manufacturing and testing capability, and it also draws samples.
  6. How long does the licence last, and does it need renewal?
    Licences are granted for a fixed term and must be renewed. Annual marking fees and surveillance audits apply while the licence is active.
  7. What happens if I sell lamps without the ISI Mark?
    You risk seizure of stock, fines and legal action under the BIS Act, and imports may be held at customs.
  8. Does certification cover all lamp types?
    No. The licence covers the lamp types and ratings listed in it. New models or ratings may need to be added.

Conclusion

BIS certification for tungsten filament lamps is a legal requirement and a mark of quality. Indian manufacturers can complete the process through the BIS portal, a factory inspection and lab testing. International manufacturers follow the FMCS route with an Authorised Indian Representative. Prepare your documents, test against IS 418:2004 in advance and plan for the timeline, and you can enter the Indian market with confidence.

Disclaimer: Fees, procedures and timelines change. Confirm current details on the official BIS website or with a BIS-recognised consultant before applying.

E-mail me when people leave their comments –

isimarkindia

You need to be a member of Global Risk Community to add comments!

Join Global Risk Community

CYSEC AFRICA 2026


CYSEC AFRICA 2026 to Convene Africa’s Cybersecurity Leaders in Johannesburg

 February 2026

CYSEC GLOBAL bringing back CYSEC AFRICA, set to take place on 26ᵗʰ February 2026 at the Gallagher Convention Centre. Under the powerful maxim, “Turning Cyber Threats into Africa’s Cyber Strength!”, The event will bring together over 250 C-level executives, CISOs, cybersecurity experts, policymakers, and technology…

Read more…
Views: 291
Comments: 0

London – January 29, 2026 – Future Alpha 2026 taking place March 31 – April 1, 2026, New York Marriott, Brooklyn Bridge is gaining unstoppable momentum. With just nine weeks to go, 100+ confirmed speakers, 30+ sponsors and exhibitors, and 800+ attendees expected - 60% from the buyside this is the premier event for quantitative finance professionals.

Headline Speakers Across Three…

Read more…
Views: 393
Comments: 0

Protecht is excited to announce a significant investment from PSG, a leading growth equity firm that specializes in partnering with high-growth software companies. This investment marks a key milestone in our journey, enabling us to accelerate innovation, expand our global reach, and continue delivering best-in-class risk management solutions to our customers, partners, and stakeholders.

Growth Equity Firm PSG invests US $280 Million in…

Read more…

On Thursday 13 March 2025, The Conduit London will host Insurance in a Changing World, a landmark conference held in the heart of London’s West End in collaboration with Howden Insurance. Bringing together more than 300 high-level leaders from cornerstone industries, including technology, insurance, risk management, philanthropic, energy and finance, this full-day gathering will explore the potential for insurance as a driver of economic growth and…

Read more…

    About Us

    The GlobalRisk Community is a thriving community of risk managers and associated service providers. Our purpose is to foster business, networking and educational explorations among members. Our goal is to be the worlds premier Risk forum and contribute to better understanding of the complex world of risk.

    Business Partners

    For companies wanting to create a greater visibility for their products and services among their prospects in the Risk market: Send your business partnership request by filling in the form here!

lead